How to carve lino
To carve lino, you cut away everything that you do not want to print. The parts that stay at full height take the ink. You draw or transfer the design onto the block, flipped, then cut the outlines with a small V gouge and clear the larger areas with a U gouge, about 1–2 mm deep. Carve away from your body, with the block held in a bench hook.
What you need
You need a lino block, two or three cutters and something to hold the block still. Most beginner kits have all of these.
| Tool | What it does |
|---|---|
| Small V gouge | Cuts outlines, fine lines and detail |
| U gouge (small and wide) | Clears areas and cuts soft, round lines |
| Handle with interchangeable blades | A cheap way to start: one handle, several blade shapes |
| Craft knife or scalpel | Straight edges, and trimming the block to size |
| Bench hook | Holds the block against the table edge, so it does not slip |
| Pencil, tracing paper, permanent marker | Put the design on the block and make it easy to see |
For kits and prices, see the best lino printing kits in the UK.
Which lino to use
Art lino is easier to carve than floor lino. There are two main kinds.
- Traditional grey lino (often on a hessian back) holds fine detail and lasts for many prints. It is firm, and it gets hard when it is cold, so warm it before you carve.
- Soft-cut or easy-carve lino is a soft vinyl block. It cuts with little force and needs no warming, which is good for beginners and children. Very fine lines can break, and you can cut it with heavy scissors.
Cheap lino can crumble or have an uneven surface. A good block costs a little more and gives cleaner lines.
Put the design on the block
The print is a mirror image of the block. Flip the design before it goes on the lino, above all text and numbers.
- Draw the design, or make it from a photo with the free PULPO! tool. The PULPO! plates are already flipped, with one plate for each colour.
- Trace the design with a soft pencil, turn the tracing paper over onto the block, and rub the back to transfer the lines. Carbon paper also works.
- Go over the lines with a permanent marker. Fill the parts that will print with marker too, so you can see what to keep and what to cut away.
Carve, step by step
- Warm the lino if it is traditional lino: about 30 seconds with a hairdryer, or a few minutes near a radiator.
- Put the block in the bench hook, against the far edge.
- Cut the outlines with the small V gouge. Hold the cutter low, at a shallow angle, and push it away from you in short, even strokes.
- Clear the areas that will not print with a U gouge. A clean channel of about 1–2 mm is usually enough. Cut a little deeper in large areas, so the roller does not touch the bottom.
- Turn the block, not your hand, when you carve curves.
- Brush away the shavings so you can see the lines.
- Make a test print (a proof). It shows the small areas that still print by mistake. Carve those, then print again.
Small ridges in large clear areas can pick up ink and print as marks. Some printmakers like these marks. If you do not want them, cut the ridges lower.
Stay safe
- Carve away from your body.
- Keep your other hand behind the blade, never in front of it.
- Use a bench hook so the block cannot slip.
- Keep your tools sharp. A sharp blade needs less force, so it slips less.
- Keep a first aid kit near you.
Look after your tools
Sharp tools cut cleaner lines and are safer. Sharpen them with a sharpening stone and a leather strop. After printing, clean the ink off with warm soapy water and dry the blades fully, so they do not rust.
Common mistakes
| Mistake | What happens | Fix |
|---|---|---|
| Text not flipped | The words print backwards | Flip the design before you transfer it |
| Cutting too deep | The block breaks or a hole goes through | Keep to 1–2 mm; deeper only in large areas |
| Blunt blade | Torn edges, and the tool slips | Sharpen it, or change the blade |
| Cold, hard lino | Carving is slow and the lines crack | Warm the block first |
| Lines too thin | Thin lines break off soft lino | Make printing lines at least about 1 mm wide |
Get a plate to carve
Turn any photo into lino plates, flipped and ready to carve, with one plate for each colour. Free, no sign-up.
Start with a photoSources
- How to cut lino for printing (Hickman Design): cutting depth, warming, tools and safety
- How to carve and print a simple linocut (Handprinted)
- Linocut (Wikipedia)
Questions
How deep should I carve lino?
About 1–2 mm is usually enough. Cut deeper in large clear areas, so that the roller does not touch the bottom. Do not cut through the block.
Which lino cutter should I start with?
A handle with interchangeable blades: a small V gouge for lines and detail, and a U gouge for clearing areas. Add a wide U gouge later for large areas.
Why is my lino hard to carve?
Traditional grey lino gets hard when it is cold. Warm it for about 30 seconds with a hairdryer, or leave it near a radiator, then carve. A blunt blade also makes carving hard: sharpen it.
Do I need to flip my design before I carve?
Yes. The print is a mirror image of the block, so text and anything that faces one way must be flipped on the block. The PULPO! plates are already flipped for carving.
How do I stop the cutter from slipping into my hand?
Use a bench hook, carve away from your body, and keep your other hand behind the blade, never in front of it. Turn the block, not your hand, when you carve a curve.